If your iPhone speaker is sounding muffled, there may be water inside it. This can happen if you’ve dropped your phone in water or gotten caught in the rain. If you think there might be water in your speaker, there are a few things you can do to try to get it out.
First, try blowing into the speaker port. This will sometimes dislodge any water that’s trapped in there. You can also try using a vacuum cleaner to suck any water out of the speaker port.
If neither of these methods work, you can try taking your iPhone apart and drying out the speaker with a hairdryer.
- If you have water in your speaker, the first step is to remove the battery
- This will help to prevent any further damage to the device
- Next, use a soft cloth or cotton swab to gently dab at the water inside of the speaker
- Avoid using anything sharp or abrasive as this could damage the speaker
- Once you have removed as much water as possible, blow into the speaker opening to help dry it out
- Finally, allow the device to sit for 24 hours before turning it on again
How to Get Water Out of Your Iphone Speaker Iphone 11
If you have an iPhone 11, you may have noticed that your speaker sounds a bit muffled. This is because water can build up in the speaker and cause it to sound distorted. If you want to clear the water out of your speaker, there are a few things you can do.
First, try using a vacuum cleaner with the hose attachment. Put the vacuum cleaner on the highest setting and hold it close to the speaker grill. Turn on the vacuum and wait for it to suck up all of the water.
If this doesn’t work, you can try using a can of compressed air. Hold the can about 6 inches away from the speaker grill and spray it for about 30 seconds. The pressure from the air will help to push any water out of the speaker.
You can also try using a hairdryer on its lowest setting. Hold the hairdryer about 6 inches away from the speaker and blow warm air into it for about 30 seconds. The heat will help evaporate any water inside of the speaker.
If none of these methods work, you may need to replace your iPhone’s speakers.
Credit: iphone-tricks.com
How Do You Get Water Out of a Speaker on Your Phone?
If your phone speaker is sounding muffled, there might be water inside it. This usually happens after dropping your phone in water or getting caught in the rain. To get the water out, you’ll need to disassemble your phone and dry out the speaker.
1. Start by removing the battery from your phone. Most phones have a removable back cover, so you’ll likely just need to pop that off and then unscrew the battery compartment. If your battery is glued in place, you’ll need to use a small tool (like a paperclip) to pry it out gently.
2. Once the battery is removed, locate the speaker on your phone. It’s usually located near the bottom of the device, and you should see a small hole where sound comes out.
3. Using a can of compressed air, blow into the speaker hole for 30 seconds or so.
This will help dislodge any water that’s trapped inside the speaker cavity.
4 . Next, use a cotton swab or Q-tip to clean any residue off of the speaker mesh (the metal part that vibrates to create sound).
You can also use a slightly dampened cloth for this step if needed.
5 . Once everything is dried off and clean, reassemble your phone and test out the speaker to see if it’s working better now!
How Do I Get Water Out of My Iphone Speaker Without Rice?
If your iPhone speaker is wet, the first thing you should do is turn it off. If it’s still on, the water could short-circuit the device. Once it’s turned off, gently wipe the water away with a lint-free cloth or cotton swab.
If you’re having trouble getting all of the water out, blow into the speaker opening to help remove any remaining liquid.
Once you’ve removed as much water as possible, you can try using rice to absorb any residual moisture. Place your iPhone in a bowl or container of uncooked rice and leave it overnight (or for at least 8 hours).
The rice will help draw out any remaining moisture from your device.
If your iPhone speaker is still not working after trying these methods, you may need to take it to a professional for repairs.
Sound To Remove Water From iPhone Speaker (GUARANTEED)
Conclusion
If you’ve ever accidentally dropped your iPhone in water, you know how frustrating it can be to try and use it afterwards. Even if you manage to get the phone working again, water damage can cause all sorts of problems down the road. That’s why it’s important to know how to get water out of your iPhone speaker as soon as possible after an accident.
The first step is to power off your phone and take out the SIM card and any other removable parts. Then, use a soft cloth or cotton swab to gently wipe away any water from the outside of the phone. Next, use a vacuum cleaner with the hose attachment to suck up any water that might be inside the speaker grille.
If you don’t have a vacuum handy, you can also try using a hairdryer on its lowest setting.
Once you’ve gotten rid of as much water as possible, put your iPhone in a bowl or container of uncooked rice and let it sit for at least 24 hours. This will help absorb any remaining moisture from inside the phone.
After that, simply dry off your iPhone and reassemble it – hopefully good as new!
