October 20

How to Light Pilot Light on Gas Water Heater

0  comments

If your gas water heater isn’t working, the first thing you should check is the pilot light. In order for the heater to function, the pilot light must be lit. If it’s not, you’ll need to relight it.

  • First, find the pilot light access panel on your gas water heater
  • Once you have located the panel, open it up and locate the pilot light assembly 3
  • Next, use a long match or lighter to ignite the pilot light 4
  • Once the pilot light is lit, turn on the gas valve to allow gas flow to the unit 5
  • Finally, close up the access panel and enjoy your newly lit water heater!

How To Light A Gas Water Heater Pilot Light

How to Light a Gas Water Heater With Electronic Pilot

If your gas water heater has an electronic pilot, you may be wondering how to light it. Here are some simple instructions to help you get started: 1. Locate the pilot light assembly on your water heater.

This is usually located near the bottom of the unit. 2. Remove the protective cover from the pilot light assembly. You may need a screwdriver to do this.

3. Press and hold the igniter button for about 30 seconds. This will allow gas to flow into the pilot light area. 4. Use a long match or lighter to ignite the gas in the pilot light area.

Once lit, release the igniter button and replace the protective cover over the assembly.

How to Light Pilot Light on Gas Water Heater

Credit: www.homeserve.com

How Do You Relight a Pilot Light on a Gas Water Heater?

If your gas water heater isn’t working, one possible reason is that the pilot light has gone out. In most cases, relighting the pilot light is a simple process. Here’s how to do it:

1. Locate the pilot light assembly on your water heater. This is usually located near the bottom of the unit. 2. Turn off the gas to your water heater at the shut-off valve.

This valve is usually located next to or near the unit. 3. Wait 5 minutes for the gas to clear from the area around the pilot light assembly before proceeding. This will help prevent any potential explosions.

4. Use a long match or lighter to relight the pilot light by igniting it at the tip of the wire inside ofthe assembly . Once you see flames coming fromthe wire, you can release it and turn onthe gas atthe shut-off valve (step 2).

Can I Relight the Pilot Light by Myself on the Water Heater?

If your water heater has a pilot light that needs to be lit, you may be wondering if you can do it yourself. The answer is yes, you can relight the pilot light on your water heater by yourself. However, before you attempt to do so, it’s important to make sure that the gas is shut off to your water heater.

Once the gas is shut off, follow these steps to relight the pilot light: 1. Locate the pilot light opening on your water heater. This is usually located near the bottom of the unit.

2. Use a long match or lighter to reach into the pilot light opening and lighting the flame. 3. Once the flame is lit, keep your hand near the opening and wait for the flame to become steady before letting go. If it does not stay lit, repeat steps 2 and 3 until it does.

4. Once the flame is steady, turn on the gas valve to your water heater (this will be located near the bottom of the unit as well). You may need to hold down on this valve for up to a minute before all ofthe gas has been turned back on. 5. Test your water heater by turning on a hot water faucet in your home – if everything was done correctly, hot water should start flowing fromthe tap almost immediately!

Can I Relight the Pilot Light by Myself?

If your gas furnace or water heater has a pilot light that needs to be lit, you may be wondering if you can do it yourself. The answer is yes, but there are some safety precautions you need to take first. Before relighting the pilot light, make sure the area around the furnace or water heater is well ventilated.

You also want to open the access panel so that any gas that does build up can escape. If possible, wear gloves and long sleeves to protect your skin from any heat or flames. Once you’re ready, follow these steps:

1) Turn off the power to the furnace or water heater. This will usually be a switch on the wall near the unit. 2) Locate the pilot light assembly and identify the knob or valve that controls the gas flow.

3) Check that this knob is in the “off” position before proceeding. 4) Find the igniter button and press it firmly several times until you hear a clicking sound (this may take a few tries). 5) While holding down the igniter button, turn on gas flow by turning knob to “pilot” position.

You should see and/or feel a difference when gas starts flowing. Keep pressing igniter button until pilot flame appears; then release both knobs/buttons. 6) Adjust pilot flame so it’s touching all sides of thermocouple (a small metal rod near tip of burner).

If necessary, use needle-nose pliers to bend thermocouple slightly so it makes good contact with pilot flame; then tighten any setscrews holding thermocouple in place. 7) Once flame is burning steadily, turn on power switch for furnace or water heater; then replace access panel(s).

How Do You Manually Light a Gas Water Heater?

If your gas water heater isn’t working, you may need to light the pilot light. Follow these steps to safely light your pilot light: 1. Make sure there is no gas leak.

If you smell gas, stop what you are doing and call your gas company immediately. 2. Find the pilot light assembly on your water heater. It will be located near the bottom of the unit.

3. Locate the knob for the gas valve and turn it to the “off” position. 4. Wait 5 minutes for any residual gas to dissipate before continuing. 5. Use a long match or lighter to ignite the pilot light flame.

Hold the flame next to the opening in the assembly where the pilot light is located until you see the flame start to take hold (this may take a minute or two). Keep in mind that natural gas is colorless and odorless, so you won’t see or smell anything when it ignites – but you should see a small blue flame once it’s lit properly. If after several attempts, you cannot get the pilot light lit, contact a qualified technician for assistance as there may be another issue with your water heater that needs attention.

.

Conclusion

If your gas water heater isn’t working, the pilot light may be out. Here’s how to light it: 1. Find the knob for the pilot light and turn it to the “on” position.

2. Use a long match or lighter to ignite the pilot light. Hold the flame to the opening for about 30 seconds, until you see the flame of the pilot light. 3. Once the flame is lit, turn on your gas valve (usually located above the pilot light knob) and wait a few minutes for hot water.


Tags


You may also like

How to Buy Best Water Purifier

How to Buy Best Water Purifier
{"email":"Email address invalid","url":"Website address invalid","required":"Required field missing"}

Subscribe to our newsletter now!