October 20

How to Replace Kitchenaid Side-By-Side Refrigerator Water Filter

0  comments

If your Kitchenaid Side-By-Side Refrigerator is equipped with a water filter, it’s important to replace it regularly. Depending on your water quality and usage, you may need to replace it as often as every six months.

How to Change Water Filter on a KitchenAid Side-by-Side Stainless Steel Fridge MODEL KSRA25ILSS01

  • Locate your water filter
  • The water filter is usually located in the grille at the bottom of your fridge
  • Remove the old water filter
  • To do this, twist the old filter counterclockwise until it comes loose from the housing
  • Insert the new water filter into the housing and twist it clockwise until it’s tight
  • Run some water through the dispenser to clear out any air bubbles and you’re done!

Kitchenaid Water Filter Stuck

When it comes to filtered water, most people think that they need a special pitcher or faucet attachment in order to get the job done. However, many refrigerators these days come equipped with a water filter, including Kitchenaid models. While this is certainly a convenient feature, it can sometimes be tricky to change the filter when it needs to be replaced – and even more so if the filter becomes stuck.

If you find yourself in this situation, don’t panic. There are a few things you can try in order to get that pesky filter unstuck and back on track. First, make sure that the area around the filter is clear and there’s nothing blocking it from coming out.

Sometimes filters can become wedged in place by debris or another object; if this is the case, simply remove whatever is causing the obstruction. If the filter still won’t budge, your next best bet is to use some lubricant on it. A little bit of WD-40 or other similar product can go a long way in helping to loosen up a stuck water filter.

Just spray a small amount onto thefilter and wait a minute or two before trying to remove it again; with any luck, it should come right out. If all else fails, your last resort is to call Kitchenaid customer service for assistance. They may be able to provide you with some additional tips or troubleshooting advice specific to your refrigerator model.

In worst case scenario, they may even be able sell you a replacement water filter (although hopefully you won’t need to go that route!).

How to Replace Kitchenaid Side-By-Side Refrigerator Water Filter

Credit: www.kitchenaid.com

How Do I Remove the Water Filter from My Kitchenaid Refrigerator?

Assuming you have a KitchenAid refrigerator with an external water filter: To remove the water filter from your KitchenAid refrigerator, first locate the filter housing on the back of the unit. Then, twist the housing to release it and pull it straight out.

Finally, twist the filter to release it from the housing and discard it according to the manufacturer’s instructions.

How Do You Change the Water Filter on a Side by Side Refrigerator?

Most side by side refrigerators have the water filter located in the grille at the bottom of the fridge. To change your water filter, first locate your model’s user manual and find the specific instructions for changing the filter. Once you know where your filter is located, follow these steps:

1. Turn off your refrigerator’s water supply. Locate the shut-off valve behind or near your fridge; turn it clockwise to close it. 2. Unscrew and remove the old water filter from its housing.

Some filters may require that you use a quarter-turn counterclockwise before pulling them out. Hold onto the old filter while doing this, as you don’t want it falling into the housing and getting lost. 3. Take a look at your new water filter to familiarize yourself with how it should be installed before proceeding.

Most filters will only fit in one way, but it doesn’t hurt to double check. 4. Insert your new water filter into its housing, screwing it in place (usually clockwise). Again, hold onto thefilter while doing this so that it doesn’t fall into the housing and get lost.

Make sure that you don’t overtighten – hand tight is usually sufficient. If there is an arrow onthefilter cartridge, make sure that it is pointing in direction of flow (into fridge) when inserted correctly intohousing .Ifyour model has a reset button or indicator light forthewaterfilter , consultyourusermanualtolearnh owtousethese features properly after installing anewfilter .

5 Reconnectyourrefrigerator’swaterlineby turning onthevalvebehindor nearit(counterclockwise). 6 Run some cold wate r throughthefreshwaterspoutinthefrontofthefridge untilyou seeareassuringstreamofwatercom ingout , whichindicatesthatthewaterlineis workingproperlyandthat thenewfilterhasbeensuccessfullyinstalled . 7 Discardanywateredthatwasleftintheoldfilterso thatyoudon’t contaminateyournewone .

How Do You Change the Air Filter on a Kitchenaid Side by Side Refrigerator?

Assuming you have a KitchenAid side by side refrigerator with the freezer on the left and the fridge on the right, open both doors. Look up at the top of the inside wall of the fridge, near where the light is located. You should see a small grille; this is where air enters the fridge to keep it cool.

The filter is located behind this grille. To remove the old filter, first locate the release button. This is usually a small tab or lever that you can press or pull to release the filter housing from its mount.

Once you’ve found and pressed/pulled the release button, carefully slide out the old filter housing (it may be hinged at one end). Take out the old filter cartridge and discard it according to your municipality’s guidelines for disposing of hazardous materials. To insert the new filter, first wet it slightly with water (this will help it seal better).

Then insert it into the housing and make sure it’s seated properly. Re-attach the housing to its mount and push until you hear it click into place. Close up your fridge and enjoy clean, filtered air!

How Do You Change the Water Filter on a Kitchenaid 5?

If your KitchenAid 5 refrigerator has a water filter located in the back, top right corner of the inside of the fridge, follow these steps to change it: 1. Remove the old filter by turning it to the left. 2. Insert the new filter into the housing and turn it to the right until it locks into place.

3. Flush out two gallons of water from the dispenser before using.

Conclusion

If your Kitchenaid side-by-side refrigerator is in need of a new water filter, don’t worry – replacing it is easy! Just follow these simple steps and you’ll have fresh, filtered water in no time. First, locate the filter housing on the ceiling of your fridge.

Then, twist the old filter to release it from the housing. Next, insert the new filter into the housing and turn it to the left to lock it into place. Finally, run water through the filter for about 2 minutes to flush out any air bubbles.

That’s all there is to it! Now you can enjoy clean, refreshing water from your Kitchenaid fridge once again.


Tags


You may also like

How to Install Lg Water Purifier

How to Install Lg Water Purifier
{"email":"Email address invalid","url":"Website address invalid","required":"Required field missing"}

Subscribe to our newsletter now!