If your Bradford White water heater isn’t working properly, you may need to reset it. Fortunately, resetting a Bradford White water heater is a relatively easy process. In most cases, you’ll just need to press a reset button on the front of the unit.
However, if your water heater is equipped with a manual gas valve, you may need to turn off the gas and restart the unit.
How to light Bradford White Hot Water Heater
- Turn off the power to the water heater by flipping the switch on the circuit breaker box
- Drain the water from the tank by attaching a hose to the drain valve and running it to a nearby drain or outside
- Remove the anode rod from the tank using a wrench and discard it
- Flush out any sediment from the tank by filling it with clean water and draining it several times
- Replace the anode rod with a new one and reattach it using a wrench
- Be sure to not overtighten as this could damage the threads on the rod or tank
- Turn on
Bradford White Defender Water Heater No Status Light
If you have a Bradford White Defender water heater, you may have noticed that there is no status light. This can be confusing, because most other models of water heaters have a green light that comes on when the power is on and a red light that comes on when the unit is heating up. So what does it mean if your Bradford White Defender doesn’t have a status light?
There are actually two possible explanations for this. First, it could simply be that the status light burned out and needs to be replaced. This isn’t uncommon, and it’s an easy fix.
Just unscrew the old lightbulb and screw in a new one.
The second possibility is that your Bradford White Defender is equipped with a feature called “Demand Defense,” which means that it doesn’t need a status light because it only heats water when there is demand for hot water (i.e., when someone turns on a faucet or shower). This feature can save energy and money, so it’s definitely something to consider if you’re looking for an efficient water heater.
Either way, if you’re wondering about the lack of a status light on your Bradford White Defender, now you know what to do!
Credit: www.youtube.com
Does a Bradford White Water Heater Have a Reset Button?
Yes, Bradford White water heaters have a reset button. This button is located on the thermostat and allows the user to manually reset the water heater if it ever goes into an error state. If your Bradford White water heater does not have a reset button, then it is likely that it is not equipped with a thermostat and cannot be manually reset.
How Do You Relight a Bradford White Water Heater?
If your Bradford White water heater is equipped with a pilot light, relighting it is a simple process. If your unit does not have a pilot light, please consult your owner’s manual for instructions on how to proceed.
To relight your water heater’s pilot light:
1) Locate the pilot light assembly on your unit. This is usually located near the bottom of the tank.
2) Turn the gas control knob to the “Pilot” position.
3) Press and hold down the reset button while you use a long match or lighter to ignite the pilot flame. Continue holding down the reset button for 30 seconds after igniting the flame. This allows time for the thermocouple to heat up and turn on the gas flow.
4) Release the reset button and turn the gas control knob to the “On” position. Your water heater should now be operational!
Why is My Bradford White Water Heater Not Heating?
There are a few reasons your Bradford White water heater might not be heating. Check the following:
1. Is there power to the unit?
If not, check the circuit breaker or fuse box.
2. Is the gas valve turned on?
3. Check that the pilot light is lit.
If it’s not, follow the instructions in your owner’s manual to relight it.
4. Once you’ve verified that there is power and gas to the unit, if it still isn’t heating, call a qualified technician for service.
Where is the Reset Button on My Water Heater?
If your water heater has a reset button, it will be located on the front of the unit near the bottom. The purpose of the reset button is to manually reset the thermal switch that controls power to the heating element. If your water heater does not have a reset button, then it is likely controlled by a circuit breaker.
Conclusion
If your Bradford White water heater isn’t working properly, you may need to reset it. To do this, first make sure that the power is off and the unit is cool. Then, remove the access panel and locate the reset button.
Press and hold the button for 30 seconds, then release it. You should hear a click as the reset process completes. If your water heater still isn’t working properly after resetting it, you may need to call a professional for further assistance.
