If your water heater’s pilot light goes out, you’ll need to relight it. Here’s how: First, locate the pilot light assembly on your water heater. On a gas water heater, the pilot light assembly is usually located near the bottom of the tank.
On an electric water heater, it’s usually located near the top of the tank. Once you’ve found the pilot light assembly, look for the knob or lever that controls the gas flow to the pilot light.
How To Light Pilot On Water Heater.
- Locate the pilot light on your water heater
- This is usually a small knob or button near the bottom of the unit
- Use a lighter to ignite the pilot light
- Hold the flame to the pilot light until it lights
- Once the pilot light is lit, you can release the knob or button
- The pilot light should stay lit on its own from this point forward
How to Relight Pilot Light on Water Heater With Igniter
If your water heater’s pilot light goes out, you can relight it using a long match or lighter. First, find the pilot light assembly on your water heater. It will be near the bottom of the unit and have a small knob that says “Pilot.”
Turn the knob to the “Off” position and wait five minutes. Then, turn it back to the “Pilot” position and hold down the knob while you light the pilot with a long match or lighter. Once the pilot is lit, release the knob and turn it back to the “On” position.
If your water heater has an igniter instead of a pilot light, follow these instructions:
1. Turn off power to water heater at circuit breaker or fuse box.
2. Remove access panel from front of water heater.
3. Locate igniter button (usually red) near gas control valve.
4. Press and hold igniter button while simultaneously depressing reset button (usually yellow) next to igniter button.
5. Hold buttons depressed for 30 seconds then release both buttons together (igniter button first).
6 .

Credit: www.homeserve.com
Can I Relight the Pilot Light by Myself on the Water Heater?
If your water heater has a pilot light that needs to be lit, you may be wondering if you can do it yourself. The answer is yes, you can relight the pilot light on your water heater by yourself. However, there are a few things you need to know before you get started.
First, make sure that the gas valve is turned to the “off” position. Then, locate the pilot light assembly on your water heater. You will see a small knob or lever near the bottom of the unit – this is what controls the gas flow to the pilot light.
Turn this knob or lever to the “off” position as well.
Now it’s time to actually relight the pilot light. Use a long match or lighter to reach down into the opening where the pilot light is located.
Turn on the gas flow by turning the knob or lever back to the “on” position, and then strike your match or lighter and hold it near the opening. The pilot light should ignite within a few seconds. Once it’s lit, continue holding the flame for about 30 seconds to give it time to heat up and stay lit on its own.
Once you’re finished, turn off both gas valves – one at your water heater and one at your home’s main gas line (if applicable). That’s all there is to it!
How Do You Turn the Pilot Light on a Water Heater?
If your water heater uses natural gas, it likely has a pilot light. The pilot light ignites the burner inside the tank to heat the water. If your pilot light goes out, you’ll need to relight it.
Here’s how:
First, locate the pilot light assembly on your water heater. It will be near the bottom of the tank and will have a small knob or lever labeled “Pilot.”
Turn off the power to your water heater. On gas water heaters, this switch is usually located above the thermostat(s). On electric water heaters, it should be near the top of the unit.
Locate the gas control valve handle on your water heater. This is usually a large knob or lever near the bottom of the unit (on gas models) or at one end (on electric models). Turn this handle to “Off.”
Wait 5 minutes for any residual gas in the line to dissipate before proceeding.
Find your lighter, and hold it close to where you’ll be lighting the pilot light (usually about 1/2 inch away). Push down on and turn the Pilot knob or lever until you hear gas flowing, then hold down on it with one hand while using your lighter with your other hand to ignite the pilot light flame.
Once you see flames coming from around where you’re holding down on Pilot knob or lever, release it; if done correctly,the flame should stay lit. If not repeat these steps until successful .
Can I Relight the Pilot Light by Myself?
If your gas stove’s pilot light goes out, you may be able to relight it yourself. But before you try, make sure that the area around the stove is well-ventilated. Then follow these steps:
1. Locate the pilot light opening on your stove. This is usually located near the front of the burner controls.
2. Lift up on the knob for the burner that you want to relight.
This will open the valve and allow gas to flow to the pilot light.
3. Use a long match or a barbecue lighter to reach into the pilot light opening and ignite the gas.
4. Hold down on the knob for about 30 seconds to give the gas time to build up and keep burning after you’ve lit it.
How Do I Get the Pilot Light Started?
If your pilot light won’t stay lit, or if you don’t have a pilot light at all, you may need to start the pilot light. Follow these steps:
1. Locate the gas valve knob.
This is usually located near the floor on the side of the fireplace.
2. Turn off the gas supply to the fireplace by turning the knob to the “off” position.
3. Wait 5 minutes for any gas that may be in the line to dissipate before proceeding.
4. Find the small hole next to where the gas valve knob is located – this is where you will insert a long thin object, like a paperclip, wire hanger or pen, to depress the reset button inside.
5. With your chosen object, depress and hold down the reset button for 30 seconds while keeping an eye on the pilot light opening at the bottom of your firebox – you should see a small flame appear within this time frame. If not, repeat steps 4 and 5 until you see aflame appear .
Keep in mind that it may take several attempts to get started!6 release The Button And turn The Gas Valve To The “On” position slowly until You Hear A click sound . Now The Pilot Light Is Lit !
Conclusion
If your home has a gas water heater, chances are it has a pilot light. This small flame is responsible for igniting the burner on your water heater, which in turn heats the water in the tank. If your pilot light goes out, you’ll need to relight it before your water heater will work again.
Follow these steps to relight your pilot light:
1. Locate the pilot light assembly on your water heater. It will be near the bottom of the unit, and may be behind a metal plate that you’ll need to remove first.
2. Once you’ve located the pilot light assembly, look for the knob or lever that controls the gas flow to the pilot light. Turn this knob or lever to “off” before proceeding.
3a.
If there is a red reset button next to the knob or lever, press and hold it while you proceed to step 3b.. otherwise skip ahead to step 4.
3b. Use a long match or lighter to relight the Pilot Light by holding it close to where the Pilot Light tube comes out of The control knob..
You may have to do this several times before Gas finally flows and lights The Pilot Light.. Be patient!
If after 30 seconds or so The Pilot Light still hasn’t lit, stop trying and go back To Step 2 because something else is wrong – most likely dirt In The gas line preventing proper flow.. Time To call A Plumber!
4 Once The Pilot Light Is Lit (or if no red Reset Button was present), turn The gas control knob slowly back To “on” until you hear Gas flowing through The igniter.. Now stand back And watch as The flames From The Pilot Light igniteThe burner and eventually heat up Your Water!