There are a few ways that you can unclog a bathtub drain full of water. One way is to use a plunger. Put the plunger over the drain and push and pull it up and down.
Another way is to use a wire hanger. Straighten out the hanger and then make a small hook on one end. Push the hook end down the drain and then twist it around to try to grab onto the clog.
- Start by removing any hair or debris that may be caught in the drain
- This can usually be done with a plunger or a drain snake
- If the drain is still clogged, you may need to use a chemical drain cleaner
- Be sure to follow the instructions on the bottle carefully, as these products can be dangerous if used improperly
- If the drain is still blocked, you may need to call a professional plumber to clear it for you
How to Unclog a Tub Drain with Standing Water
How Do You Unclog a Full Bathtub of Water?
If your bathtub is full of water and won’t drain, you may need to unclog it. There are a few ways to do this, but the most common is to use a plunger. If you don’t have a plunger, you can try using a wire hanger or a plumber’s snake.
To use a plunger, start by putting on some rubber gloves. This will protect your hands from the dirty water. Next, place the plunger over the drain and make sure there is a tight seal.
Then, push and pull the plunger up and down vigorously for 30 seconds or so. If the water starts draining, continue doing this until it is all gone. If the water doesn’t start draining after 30 seconds or so, try another method.
To use a wire hanger, start by straightening out the hanger and then making a small hook at one end. Next, insert the hooked end into the drain and move it around until you feel resistance. Once you feel resistance, pull on the hanger and see if anything comes out of the drain (this will likely be hair and gunk).
If nothing comes out after several tries, move on to another method.
To use a plumber’s snake, start by inserting the snake into the drain until you feel resistance (it may take some wiggling to get past any clogs). Once you feel resistance, turnthe crank handle clockwise while pushing down lightly onthe snake – this will help to break through any clogs.
Continue doing this untilyou feel thatthe clog has been cleared away .
How Do You Unclog a Drain With Standing Water?
If you have a clogged drain with standing water, there are a few ways you can unclog it. First, try using a plunger to see if that will dislodge the clog. If the plunger doesn’t work, you can try using a plumber’s snake or an auger.
Put the snake or auger into the drain and turn it until you feel resistance. This should help to break up the clog. If neither of these methods works, you may need to call a plumber.
How Do You Unclog a Bathtub That Won’T Drain?
If your bathtub won’t drain, there are a few things you can do to try and unclog it yourself. First, check to see if the stopper is blocking the drain. If so, remove the stopper and try clearing the drain with a plunger or a snake.
If neither of those work, you may need to remove the P-trap beneath the sink to clear the blockage.
Why is There Standing Water in My Bathtub Drain?
If you notice standing water in your bathtub drain, there could be a few different reasons why. A common reason is that the P-trap, which is a U-shaped pipe under the sink that holds water to prevent sewer gases from coming back up through the drain, may be blocked or clogged. Another possibility is that the vent stack, which helps regulate air pressure in the drains and allows sewage gases to escape, could be blocked.
If you determine that the P-trap is indeed blocked or clogged, you can try to clear it out yourself with a plunger or a snake (a long, flexible metal rod). If these methods don’t work or if you’re not comfortable trying them yourself, you can always call a plumber.
As for the vent stack, if it’s blocked then sewage could start backing up into your home so it’s important to address this issue as soon as possible.
The best way to do this is again with a plunger or a snake. If these don’t work, then you’ll need to call a professional since they’ll likely need to access the roof in order to clear out the blockage.

Credit: www.youtube.com
Bathtub Full of Water Won’T Drain
If you have a bathtub full of water that won’t drain, there are a few things you can do to try and fix the problem. First, check to see if there is anything blocking the drain. If there is, try to remove it with a plunger or a plumber’s snake.
If that doesn’t work, your next step is to pour a cup of baking soda down the drain, followed by a cup of vinegar. Let the mixture sit for 15 minutes, then run hot water down the drain to see if that does the trick. If not, your final option is to call a plumber.
Conclusion
If your bathtub is full of water and won’t drain, there are a few things you can do to try and unclog it. First, try using a plunger to see if that will dislodge the clog. If that doesn’t work, you can try using a plumber’s snake or an auger to reach down into the drain and clear the clog manually.
Finally, if all else fails, you may need to remove the drain cover and clean out the drain trap beneath.